מחיר וייעוץ למוצר הזהדברו עם יועץ ובחרו את הפתרון שמתאים לכםפרטי המוצר מצורפים אוטומטית להודעת הוואטסאפ
עד 7 ימי עסקים בלבד
בהזמנות מעל 2000 ש״ח
הכוונה וייעוץ לפני רכישה
בהזמנות אונליין באתר
PLANET WGS-804HPT — מתג תעשייתי מנוהל. מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
Industrial Managed Ethernet Switch. PLANET WGS-804HPT connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
PLANET WGS-804HPT · מתגים תעשייתיים
PLANET WGS-804HPT מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
8-Port 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
IEEE 802.3af/802.3at Power over Ethernet PSE
144 watts (depending on power input)
48~54V DC, 4A (max.)
Wall mount, magnetic wall mount and DIN-rail kit
IP30 metal
בתכנון ארון תקשורת למפעל, מערכת בקרה או תשתית אבטחה, חשוב להתאים את מספר החיבורים ואת רוחב הפס לכל קצה. חיבורי Uplink, כאשר הם קיימים בדגם, משמשים לקישור לשאר הרשת. בממשק SFP יש להתאים את המודול, סוג הסיב ואורך הקו לשני קצות הקישור.
הדגם כולל תמיכה ב־VLAN, ACL, LACP, ERPS, SNMP, IPv6 לפי המפרט. יכולות אלה מאפשרות להתאים את הגדרות הרשת לפרויקט; מגדירים כל תכונה לפי תכנון התעבורה וממשקי הציוד המחובר.
טבלת המפרט באנגלית מרכזת את נתוני הדגם לצורך השוואה והתאמה טכנית. יש להתאים את ההזנה, החיבורים ותנאי הסביבה לערכים המפורטים. צוות סיבים מסייע בבחירת הציוד והתצורה המתאימים לפרויקט.
The PLANET WGS-804HPT connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
For factory networks, control systems and surveillance infrastructure, plan both the number of device connections and the uplink capacity. Where SFP interfaces are provided, the transceiver type, fiber type and link distance must match the equipment at both ends. Copper and fiber ports are listed separately to make this planning easier.
The technical table below provides the model-specific information for comparison and system design. Match the power source, connectors and environmental conditions to these ratings. SIVIM can assist with equipment selection and configuration for the project.
| Specification | Details |
|---|---|
| Manufacturer / Model | PLANET WGS-804HPT |
| Copper Ports | 8-Port 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports |
| PoE Inject Port | 4-Port with 802.3af/802.3at PoE injector function (Port-1 to Port-4) |
| Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
| Connector | Removable 3-pin terminal block for power input Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-) Pin 3 for earth ground DC power jack with 2.0mm central pole |
| Power Requirements | 48~54V DC, 4A (max.) |
| Power Consumption/ Dissipation | DC 48V – 2.4W/8.19BTU/hr (no loading); 155.2W/529.56BTU/hr (full loading) DC 54V – 2.7W/9.21BTU/hr (no loading); 154.6W/527.52BTU/hr (full loading) |
| Dimensions (W x D x H) | 148 x 24.2 x 134 mm |
| Weight | 532g |
| ESD Protection | Contact Discharge 4KV DC Air Discharge 8KV DC |
| Enclosure | IP30 metal |
| Installation | Wall mount, magnetic wall mount and DIN-rail kit |
| LED | Power LED: Power ( Green ) PoE Power Usage LED: 30W, 60W, 90W, 120W ( Amber ) PoE Port(Port-1 to Port-4) : PoE-in-Use ( Amber ) LNK/ACT ( Green ) 10/100/1000BASE-TX Port (Port-5 to Port-8) : 1000 ( Green ) LNK/ACT ( Green ) |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 16Gbps/non-blocking |
| Switch Throughput@64 bytes | 11.9Mpps @64 bytes |
| MAC Address Table | 8K entries |
| Shared Data Buffer | 4.1 megabits |
| Flow Control | IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex |
| Jumbo Frame | 10KB |
| PoE Standard | IEEE 802.3af/802.3at Power over Ethernet PSE |
| PoE Power Supply Type | End-span |
| PoE Power Output | IEEE 802.3af Standard Per port 48V~54V DC (depending on the power supply), max. 15.4 watts IEEE 802.3at Standard Per port 50V~54V DC (depending on the power supply), max. 36 watts |
| PoE Power Budget | 144 watts (depending on power input) |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| PoE Management | PD Alive Check Scheduled Power Recycling PoE Schedule PoE Usage Monitoring PoE Extension |
| Enhanced PoE Mode | Standard/Legacy/Force |
| Active PoE Device Live Detection | Yes |
| PoE Power Recycling | Yes, daily or predefined schedule |
| PoE Schedule | 4 schedule profiles |
| PoE Extend Mode | Yes, max. up to 250 meters |
| Port Mirroring | TX/RX/Both Many-to-1 monitor Up to 4 sessions |
| VLAN | 802.1Q tagged VLAN Up to 256 VLAN groups, out of 4094 VLAN IDs 802.1ad Q-in-Q tunneling (VLAN stacking) Voice VLAN Protocol VLAN Private VLAN (Protected port) GVRP Management VLAN |
| Link Aggregation | IEEE 802.3ad LACP and static trunk Supports 4 groups with 8 ports per trunk |
| Spanning Tree Protocol | STP, IEEE 802.1D Spanning Tree Protocol RSTP, IEEE 802.1w Rapid Spanning Tree Protocol MSTP, IEEE 802.1s Multiple Spanning Tree Protocol STP BPDU Guard, BPDU Filtering and BPDU Forwarding |
| IGMP Snooping | IPv4 IGMP (v2/v3) snooping IGMP querier Up to 256 multicast groups |
| MLD Snooping | IPv6 MLD (v1/v2) snooping, up to 256 multicast groups |
| QoS | 8 mapping ID to 8 level priority queues Port Number 802.1p priority DSCP/IP precedence of IPv4/IPv6 packets Traffic classification based, strict priority and WRR Ingress/Egress Rate Limit per port bandwidth control |
| Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 450ms |
| Access Control List | IPv4/IPv6 IP-based ACL/MAC-based ACL IPv4/IPv6 IP-based ACE/MAC-based ACE Max. 256 ACL entries |
| Port Security | IEEE 802.1X – Port-based authentication Built-in RADIUS client to co-operate with RADIUS server RADIUS/TACACS+ user access authentication |
| MAC Security | IP-MAC port binding MAC filter Static MAC address, Max. 256 static MAC entries |
| Enhanced Security | DHCP Snooping and DHCP Option82 STP BPDU guard, BPDU filtering and BPDU forwarding DoS attack prevention ARP inspection IP source guard |
| Basic Management Interfaces | Web browser; Telnet; SNMP v1, v2c |
| Secure Management Interfaces | SSHv2, TLS v1.2, SNMPv3 |
| Switch Management | Firmware upgrade by HTTP/TFTP protocol through Ethernet network Configuration upload/download through HTTP/TFTP LLDP protocol SNTP PLANET Smart Discovery Utility PLANET NMS System/CloudViewer |
| Event Management | Remote/Local Syslog System log |
| SNMP MIBs | RFC 1213 MIB-II RFC 1215 Generic Traps RFC 1493 Bridge MIB RFC 2674 Bridge MIB Extensions RFC 2737 Entity MIB (Version 2) RFC 2819 RMON (1, 2, 3, 9) RFC 2863 Interface Group MIB RFC 3635 Ethernet-like MIB RFC 3621 Power Ethernet MIB |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Stability Testing | IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000BASE-T IEEE 802.3x Flow Control and Back Pressure IEEE 802.3ad Port Trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN Tagging IEEE 802.1x Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy Efficient Ethernet (EEE) RFC 768 UDP RFC 793 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 RFC 3810 MLD v2 ITU G.8032 ERPS Ring |
| Operating | Temperature: -40 ~ 75 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage | Temperature: -40 ~ 85 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Standard Accessories | Quick Installation Guide QR Code sheet x 1 3-pin Terminal Block Connector x 1 Wall mount Kit x 1 DIN-rail mount Kit x 1 Magnet mount Kit x 1 RJ45 Dust Cap x 8 |
| Model | WGS-804HPT |
|---|---|
| Copper Ports | 8-Port 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports |
| PoE Inject Port | 4-Port with 802.3af/802.3at PoE injector function (Port-1 to Port-4) |
| Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
| Connector | Removable 3-pin terminal block for power input Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-) Pin 3 for earth ground DC power jack with 2.0mm central pole |
| Power Requirements | 48~54V DC, 4A (max.) |
| Power Consumption/ Dissipation | DC 48V – 2.4W/8.19BTU/hr (no loading); 155.2W/529.56BTU/hr (full loading) DC 54V – 2.7W/9.21BTU/hr (no loading); 154.6W/527.52BTU/hr (full loading) |
| Dimensions (W x D x H) | 148 x 24.2 x 134 mm |
| Weight | 532g |
| ESD Protection | Contact Discharge 4KV DC Air Discharge 8KV DC |
| Enclosure | IP30 metal |
| Installation | Wall mount, magnetic wall mount and DIN-rail kit |
| LED | Power LED: Power ( Green ) PoE Power Usage LED: 30W, 60W, 90W, 120W ( Amber ) PoE Port(Port-1 to Port-4) : PoE-in-Use ( Amber ) LNK/ACT ( Green ) 10/100/1000BASE-TX Port (Port-5 to Port-8) : 1000 ( Green ) LNK/ACT ( Green ) |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 16Gbps/non-blocking |
| Switch Throughput@64 bytes | 11.9Mpps @64 bytes |
| MAC Address Table | 8K entries |
| Shared Data Buffer | 4.1 megabits |
| Flow Control | IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex |
| Jumbo Frame | 10KB |
| PoE Standard | IEEE 802.3af/802.3at Power over Ethernet PSE |
| PoE Power Supply Type | End-span |
| PoE Power Output | IEEE 802.3af Standard Per port 48V~54V DC (depending on the power supply), max. 15.4 watts IEEE 802.3at Standard Per port 50V~54V DC (depending on the power supply), max. 36 watts |
| PoE Power Budget | 144 watts (depending on power input) |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| PoE Management | PD Alive Check Scheduled Power Recycling PoE Schedule PoE Usage Monitoring PoE Extension |
| Enhanced PoE Mode | Standard/Legacy/Force |
| Active PoE Device Live Detection | Yes |
| PoE Power Recycling | Yes, daily or predefined schedule |
| PoE Schedule | 4 schedule profiles |
| PoE Extend Mode | Yes, max. up to 250 meters |
| Port Mirroring | TX/RX/Both Many-to-1 monitor Up to 4 sessions |
| VLAN | 802.1Q tagged VLAN Up to 256 VLAN groups, out of 4094 VLAN IDs 802.1ad Q-in-Q tunneling (VLAN stacking) Voice VLAN Protocol VLAN Private VLAN (Protected port) GVRP Management VLAN |
| Link Aggregation | IEEE 802.3ad LACP and static trunk Supports 4 groups with 8 ports per trunk |
| Spanning Tree Protocol | STP, IEEE 802.1D Spanning Tree Protocol RSTP, IEEE 802.1w Rapid Spanning Tree Protocol MSTP, IEEE 802.1s Multiple Spanning Tree Protocol STP BPDU Guard, BPDU Filtering and BPDU Forwarding |
| IGMP Snooping | IPv4 IGMP (v2/v3) snooping IGMP querier Up to 256 multicast groups |
| MLD Snooping | IPv6 MLD (v1/v2) snooping, up to 256 multicast groups |
| QoS | 8 mapping ID to 8 level priority queues Port Number 802.1p priority DSCP/IP precedence of IPv4/IPv6 packets Traffic classification based, strict priority and WRR Ingress/Egress Rate Limit per port bandwidth control |
| Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 450ms |
| Access Control List | IPv4/IPv6 IP-based ACL/MAC-based ACL IPv4/IPv6 IP-based ACE/MAC-based ACE Max. 256 ACL entries |
| Port Security | IEEE 802.1X – Port-based authentication Built-in RADIUS client to co-operate with RADIUS server RADIUS/TACACS+ user access authentication |
| MAC Security | IP-MAC port binding MAC filter Static MAC address, Max. 256 static MAC entries |
| Enhanced Security | DHCP Snooping and DHCP Option82 STP BPDU guard, BPDU filtering and BPDU forwarding DoS attack prevention ARP inspection IP source guard |
| Basic Management Interfaces | Web browser; Telnet; SNMP v1, v2c |
| Secure Management Interfaces | SSHv2, TLS v1.2, SNMPv3 |
| Switch Management | Firmware upgrade by HTTP/TFTP protocol through Ethernet network Configuration upload/download through HTTP/TFTP LLDP protocol SNTP PLANET Smart Discovery Utility PLANET NMS System/CloudViewer |
| Event Management | Remote/Local Syslog System log |
| SNMP MIBs | RFC 1213 MIB-II RFC 1215 Generic Traps RFC 1493 Bridge MIB RFC 2674 Bridge MIB Extensions RFC 2737 Entity MIB (Version 2) RFC 2819 RMON (1, 2, 3, 9) RFC 2863 Interface Group MIB RFC 3635 Ethernet-like MIB RFC 3621 Power Ethernet MIB |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Stability Testing | IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000BASE-T IEEE 802.3x Flow Control and Back Pressure IEEE 802.3ad Port Trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN Tagging IEEE 802.1x Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy Efficient Ethernet (EEE) RFC 768 UDP RFC 793 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 RFC 3810 MLD v2 ITU G.8032 ERPS Ring |
| Operating | Temperature: -40 ~ 75 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage | Temperature: -40 ~ 85 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Standard Accessories | Quick Installation Guide QR Code sheet x 1 3-pin Terminal Block Connector x 1 Wall mount Kit x 1 DIN-rail mount Kit x 1 Magnet mount Kit x 1 RJ45 Dust Cap x 8 |
© כל הזכויות שמורות לסיבים תשתיות תקשורת
פרסום בפייסבוק ע"י קרית טק
