מחיר וייעוץ למוצר הזהדברו עם יועץ ובחרו את הפתרון שמתאים לכםפרטי המוצר מצורפים אוטומטית להודעת הוואטסאפ
עד 7 ימי עסקים בלבד
בהזמנות מעל 2000 ש״ח
הכוונה וייעוץ לפני רכישה
בהזמנות אונליין באתר
PLANET ISW-504PT — מתג תעשייתי לא מנוהל PoE+. מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
Industrial Unmanaged PoE+ Switch. PLANET ISW-504PT connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
PLANET ISW-504PT · מתגים תעשייתיים
PLANET ISW-504PT מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
Five 10/100BASE-TX RJ45 auto-MDI/MDI-X ports (Ports 1 to 5)
IEEE 802.3at Power over Ethernet Plus/PSE
120W maximum @54V DC 90W maximum@24V DC 60W maximum@12V DC
12~54V DC, 7A (max.)
DIN-rail/ wall-mount
IP40 metal case
בתכנון ארון תקשורת למפעל, מערכת בקרה או תשתית אבטחה, חשוב להתאים את מספר החיבורים ואת רוחב הפס לכל קצה. חיבורי Uplink, כאשר הם קיימים בדגם, משמשים לקישור לשאר הרשת. בממשק SFP יש להתאים את המודול, סוג הסיב ואורך הקו לשני קצות הקישור.
טבלת המפרט באנגלית מרכזת את נתוני הדגם לצורך השוואה והתאמה טכנית. יש להתאים את ההזנה, החיבורים ותנאי הסביבה לערכים המפורטים. צוות סיבים מסייע בבחירת הציוד והתצורה המתאימים לפרויקט.
The PLANET ISW-504PT connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
For factory networks, control systems and surveillance infrastructure, plan both the number of device connections and the uplink capacity. Where SFP interfaces are provided, the transceiver type, fiber type and link distance must match the equipment at both ends. Copper and fiber ports are listed separately to make this planning easier.
The technical table below provides the model-specific information for comparison and system design. Match the power source, connectors and environmental conditions to these ratings. SIVIM can assist with equipment selection and configuration for the project.
| Specification | Details |
|---|---|
| Manufacturer / Model | PLANET ISW-504PT |
| Copper Ports | Five 10/100BASE-TX RJ45 auto-MDI/MDI-X ports (Ports 1 to 5) |
| PoE Injector Ports | Four ports with 802.3af/at PoE+ injector function (Ports 1 to 4) |
| Connector | Removable 6-pin terminal block Pin 1/2 for Power 1 Pin 3/4 for power fault alarm Pin 5/6 for Power 2 |
| DIP Switch (Ports 1 to 4) | Standard mode: 30-watt PoE transmission distance of 100m at speed of 10/100Mbps VLAN mode: "Port-based VLAN Protection" where ports can be isolated from each other via one DIP switch. Only Port 5 can visit other ports. Extend mode: 25-watt PoE transmission distance of 250m at speed of 10Mbps |
| Power Requirements | 12~54V DC, 7A (max.) |
| Power Consumption | Max. 6.48 watts/22BTU@54V DC input (System) Max. 133 watts/453BTU@54V DC input (Ethernet + PoE Full Loading) |
| Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24V AC |
| Dimensions (W x D x H) | 50 x 87.8 x 135 mm |
| Weight | 613g |
| Enclosure | IP40 metal case |
| Installation | DIN-rail/ wall-mount |
| ESD Protection | 5KV |
| LED Indicators | 3 x LED for System and Power: Green : DC Power 1 Green : DC Power 2 Red : Power Fault Alarm 2 x LED for PoE +Copper Port (Ports 1 to 4): Green : LNK/ACT (10/100Mbps) Amber : PoE-in-Use 1 x LED for Copper Port (Port-5): Green : LNK/ACT (10/100Mbps) 4 x LED for PoE Usage(W) (Low to high): Amber : 30W, 60W, 90W and 120W |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 1Gbps/non-blocking |
| Throughput (packet per second) | 0.74Mpps @64 bytes |
| Address Table | 1K entries |
| Jumbo Frame | 1536 bytes |
| Flow Control | Back pressure for half duplex IEEE 802.3x pause frame for full duplex |
| PoE Standard | IEEE 802.3at Power over Ethernet Plus/PSE |
| PoE Power Supply Type | End-span |
| Power Pin Assignment | 1/2 (+), 3/6 (-) |
| PoE Power Output | Per port 54V DC, Max. 36 watts |
| PoE Power Budget (max.) | 120W maximum @54V DC 90W maximum@24V DC 60W maximum@12V DC |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Stability Testing | IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3x Flow Control and Back Pressure IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus PROFINET Traffic Pass-through with QoS |
| Temperature | Operating: -40~75 degrees C Storage: -40~85 degrees C |
| Humidity | Operating: 5~90% (non-condensing) Storage: 5~90% (non-condensing) |
| Model | ISW-504PT |
|---|---|
| Copper Ports | Five 10/100BASE-TX RJ45 auto-MDI/MDI-X ports (Ports 1 to 5) |
| PoE Injector Ports | Four ports with 802.3af/at PoE+ injector function (Ports 1 to 4) |
| Connector | Removable 6-pin terminal block Pin 1/2 for Power 1 Pin 3/4 for power fault alarm Pin 5/6 for Power 2 |
| DIP Switch (Ports 1 to 4) | Standard mode: 30-watt PoE transmission distance of 100m at speed of 10/100Mbps VLAN mode: "Port-based VLAN Protection" where ports can be isolated from each other via one DIP switch. Only Port 5 can visit other ports. Extend mode: 25-watt PoE transmission distance of 250m at speed of 10Mbps |
| Power Requirements | 12~54V DC, 7A (max.) |
| Power Consumption | Max. 6.48 watts/22BTU@54V DC input (System) Max. 133 watts/453BTU@54V DC input (Ethernet + PoE Full Loading) |
| Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24V AC |
| Dimensions (W x D x H) | 50 x 87.8 x 135 mm |
| Weight | 613g |
| Enclosure | IP40 metal case |
| Installation | DIN-rail/ wall-mount |
| ESD Protection | 5KV |
| LED Indicators | 3 x LED for System and Power: Green : DC Power 1 Green : DC Power 2 Red : Power Fault Alarm 2 x LED for PoE +Copper Port (Ports 1 to 4): Green : LNK/ACT (10/100Mbps) Amber : PoE-in-Use 1 x LED for Copper Port (Port-5): Green : LNK/ACT (10/100Mbps) 4 x LED for PoE Usage(W) (Low to high): Amber : 30W, 60W, 90W and 120W |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 1Gbps/non-blocking |
| Throughput (packet per second) | 0.74Mpps @64 bytes |
| Address Table | 1K entries |
| Jumbo Frame | 1536 bytes |
| Flow Control | Back pressure for half duplex IEEE 802.3x pause frame for full duplex |
| PoE Standard | IEEE 802.3at Power over Ethernet Plus/PSE |
| PoE Power Supply Type | End-span |
| Power Pin Assignment | 1/2 (+), 3/6 (-) |
| PoE Power Output | Per port 54V DC, Max. 36 watts |
| PoE Power Budget (max.) | 120W maximum @54V DC 90W maximum@24V DC 60W maximum@12V DC |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Stability Testing | IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3x Flow Control and Back Pressure IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus PROFINET Traffic Pass-through with QoS |
| Temperature | Operating: -40~75 degrees C Storage: -40~85 degrees C |
| Humidity | Operating: 5~90% (non-condensing) Storage: 5~90% (non-condensing) |
© כל הזכויות שמורות לסיבים תשתיות תקשורת
פרסום בפייסבוק ע"י קרית טק
