מחיר וייעוץ למוצר הזהדברו עם יועץ ובחרו את הפתרון שמתאים לכםפרטי המוצר מצורפים אוטומטית להודעת הוואטסאפ
עד 7 ימי עסקים בלבד
בהזמנות מעל 2000 ש״ח
הכוונה וייעוץ לפני רכישה
בהזמנות אונליין באתר
PLANET BSP-360 — מתג PoE סולארי. משלב תקשורת Ethernet והזנת PoE במערכת המבוססת על מקורות האנרגיה הנתמכים בדגם. הוא מיועד לפרויקטים שבהם צריך להפעיל ציוד רשת באתר מרוחק ולתכנן יחד את קישור הנתונים ואת אספקת החשמל.
Solar-Powered PoE Switch. PLANET BSP-360 combines Ethernet connectivity and PoE power in a system using the energy sources supported by this model. It is intended for remote installations where the network connection and power supply must be designed together.
PLANET BSP-360 · פתרונות PoE תעשייתיים
PLANET BSP-360 משלב תקשורת Ethernet והזנת PoE במערכת המבוססת על מקורות האנרגיה הנתמכים בדגם. הוא מיועד לפרויקטים שבהם צריך להפעיל ציוד רשת באתר מרוחק ולתכנן יחד את קישור הנתונים ואת אספקת החשמל.
LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 1 to Port 5, bridge mode) WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 5, gateway mode)
IEEE 802.3af/802.3at Power over Ethernet PSE
120 watts (PoE consumption + DC out and depending on power input)
PV in: 24~45V DC Battery in/out: 24V DC
4 PoE out 51VDC; max. 36 watts per PoE port 2 DC out 24@ 2A maximum (four-pin terminal block) * The voltage of DC out is based on the battery.
DIN-rail kit and wall-mount ear
במערכת סולארית מתאימים את הפאנל, המצבר, מתחי העבודה וזרם הטעינה לדגם המדויק. זמן העבודה תלוי בצריכת הציוד, בקיבולת המצבר ובתנאי הטעינה. ציוד חיצוני ואביזרי מערכת נבחרים כחלק מתכנון הפרויקט.
טבלת המפרט באנגלית מרכזת את נתוני הדגם לצורך השוואה והתאמה טכנית. יש להתאים את ההזנה, החיבורים ותנאי הסביבה לערכים המפורטים. צוות סיבים מסייע בבחירת הציוד והתצורה המתאימים לפרויקט.
The PLANET BSP-360 combines Ethernet connectivity and PoE power in a system using the energy sources supported by this model. It is intended for remote installations where the network connection and power supply must be designed together.
Match the solar panel, battery, operating voltages and charging current to the exact model. Runtime depends on device consumption, battery capacity and charging conditions. External equipment and system accessories must be selected as part of the project design.
The technical table below provides the model-specific information for comparison and system design. Match the power source, connectors and environmental conditions to these ratings. SIVIM can assist with equipment selection and configuration for the project.
| Specification | Details |
|---|---|
| Manufacturer / Model | PLANET BSP-360 |
| Copper Ports | LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 1 to Port 5, bridge mode) WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 5, gateway mode) |
| PoE Injector Port | 4 ports with 802.3af/802.3at PoE injector function (Port 1 to Port 4) |
| USB | 1 USB Type A female for setting backup |
| Power Output | 4 PoE out 51VDC; max. 36 watts per PoE port 2 DC out 24@ 2A maximum (four-pin terminal block) * The voltage of DC out is based on the battery. |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 10Gbps/non-blocking |
| Switch Throughput@64 bytes | 5.95Mpps@64 bytes |
| MAC Address Table | 8K entries |
| Shared Data Buffer | 512Kbit |
| Flow Control | IEEE 802.3x pause frame for full duplex Back pressure for half duplex |
| Reset Button | < 5 sec: System reboot > 10 sec: Factory default |
| LED Indicators | 3 LEDs for System and Power: – Green: Power – Red: Alarm – Green: PV System 4 LEDs for PoE Copper Ports (Port 1~Port 4): – Green: LNK/ACT – Amber: PoE-in-use 1 LED for 10/100/1000T Copper Port (Port 5): – Green: LNK/ACT 3 LEDs for PoE Power Usage (W) – Amber: 50, 100 and 120W |
| Connector | Removable 6-pin terminal block Pin 1/2 for PV panel; Pin 3/4 for alarm; Pin 5/6 for battery |
| Alarm | 1 digital output (DO): Level 0: -24V~2.1V (±0.1V) Level 1: 2.1V~24V (±0.1V) Open collector to 24V DC, 100mA max. |
| Power Requirements | PV in: 24~45V DC Battery in/out: 24V DC |
| Power Consumption/ Dissipation | 5.04 watts, 17.1BTU (Standby without PoE function) 6.96 watts, 23.7 BTU (Full loading without PoE function) 135.36 watts, 461.5 BTU (Full loading with PoE function) |
| Dimensions (W x D x H) | 86.8 x 107.3 x 152 mm |
| Weight | 1251g |
| ESD Protection | 6KV DC |
| Enclosure | IP30 aluminum case |
| Installation | DIN-rail kit and wall-mount ear |
| PoE Standard | IEEE 802.3af/802.3at Power over Ethernet PSE |
| PoE Power Supply Type | End-span |
| PoE Power Output | Per port 51V DC, 275mA. Max. 15.4 watts (IEEE 802.3af) Per port 51V DC, 535mA. Max. 36 watts (IEEE 802.3at) |
| Power Pin Assignment | 1/2 (+), 3/6 (-) |
| PoE Power Budget | 120 watts (PoE consumption + DC out and depending on power input) |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| Min. Voltage | 24V (Suggest > 30V for fully charge to battery) |
| Max. Voltage | 45V |
| Max. Current | < 8.8A |
| Max. Power | < 400W |
| Type | Lithium Battery (Default) Lead-acid Battery |
| FCV | Lithium Battery (Default) fixed 26.6V Lead-acid Battery 27.2V (26.0~30.0V) |
| ACV | Lithium Battery (Default) fixed 28.7V Lead-acid Battery 29.2V (28.0~32.0V) |
| LVD (Low Voltage Disconnection) | Lithium Battery (Default) 21.3V (19.6~23.0V) Lead-acid Battery 22.2V (21.0~23.0V) |
| LVR (Low Voltage Reconnection) | Lithium Battery (Default) 24.0V (23.5~25.0V) Lead-acid Battery 23.5V (23.5~27.0V) |
| Internet Connection Type | Shares data and Internet access with users, supporting the following internet accesses: – PPPoE – Dynamic IP – Static IP – PPTP – L2TP |
| Firewall | NAT firewall with SPI (Stateful Packet Inspection) Built-in NAT server supporting Port Forwarding, and DMZ Built-in firewall with IP address/MAC address/Port/ URL filtering Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter, DoS protection |
| Routing Protocol | Static/Dynamic (RIP1 and 2) routing |
| VPN Pass-through | PPTP, L2TP, IPSec, IPv6 |
| LAN | Built-in DHCP server supporting static IP address distribution Supports UPnP, Dynamic DNS Supports IGMP Proxy Supports 802.1d STP (Spanning Tree) IP/MAC-based bandwidth control |
| Management Interface | Setting up of system/management functions Web firmware upgrade SNMP trap for alarm notification of events |
| PoE Management | Power limit by consumption and allocation PoE admin mode Per port power schedule Per port power enable/disable Power feeding priority Current per port usage and status Total power consumption PD alive check Scheduled power recycling |
| Battery Management | Current battery usage status Low voltage cut-off protection Fully-charged hold time protection |
| PLANET ONVIF IP Camera Management | Supports PLANET ONVIF IP camera discovery A maximum of four PLANET ONVIF IP cameras can be powered by one BSP-360 switch. Supports IP camera snapshot function in the LAN. |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Standards Compliance | IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3x Flow Control and Back Pressure IEEE 802.1D Spanning Tree Protocol IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus RFC 768: UDP RFC 791: IP RFC 2068 HTTP RFC 1157: SNMP v1 RFC 1902: SNMP v2c RFC 5424: Syslog |
| Operating | Temperature: -10 ~ 60 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage | Temperature: -10 ~ 70 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Model | BSP-360 |
|---|---|
| Copper Ports | LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 1 to Port 5, bridge mode) WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 5, gateway mode) |
| PoE Injector Port | 4 ports with 802.3af/802.3at PoE injector function (Port 1 to Port 4) |
| USB | 1 USB Type A female for setting backup |
| Power Output | 4 PoE out 51VDC; max. 36 watts per PoE port 2 DC out 24@ 2A maximum (four-pin terminal block) * The voltage of DC out is based on the battery. |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 10Gbps/non-blocking |
| Switch Throughput@64 bytes | 5.95Mpps@64 bytes |
| MAC Address Table | 8K entries |
| Shared Data Buffer | 512Kbit |
| Flow Control | IEEE 802.3x pause frame for full duplex Back pressure for half duplex |
| Reset Button | < 5 sec: System reboot > 10 sec: Factory default |
| LED Indicators | 3 LEDs for System and Power: - Green: Power - Red: Alarm - Green: PV System 4 LEDs for PoE Copper Ports (Port 1~Port 4): - Green: LNK/ACT - Amber: PoE-in-use 1 LED for 10/100/1000T Copper Port (Port 5): - Green: LNK/ACT 3 LEDs for PoE Power Usage (W) - Amber: 50, 100 and 120W |
| Connector | Removable 6-pin terminal block Pin 1/2 for PV panel; Pin 3/4 for alarm; Pin 5/6 for battery |
| Alarm | 1 digital output (DO): Level 0: -24V~2.1V (±0.1V) Level 1: 2.1V~24V (±0.1V) Open collector to 24V DC, 100mA max. |
| Power Requirements | PV in: 24~45V DC Battery in/out: 24V DC |
| Power Consumption/ Dissipation | 5.04 watts, 17.1BTU (Standby without PoE function) 6.96 watts, 23.7 BTU (Full loading without PoE function) 135.36 watts, 461.5 BTU (Full loading with PoE function) |
| Dimensions (W x D x H) | 86.8 x 107.3 x 152 mm |
| Weight | 1251g |
| ESD Protection | 6KV DC |
| Enclosure | IP30 aluminum case |
| Installation | DIN-rail kit and wall-mount ear |
| PoE Standard | IEEE 802.3af/802.3at Power over Ethernet PSE |
| PoE Power Supply Type | End-span |
| PoE Power Output | Per port 51V DC, 275mA. Max. 15.4 watts (IEEE 802.3af) Per port 51V DC, 535mA. Max. 36 watts (IEEE 802.3at) |
| Power Pin Assignment | 1/2 (+), 3/6 (-) |
| PoE Power Budget | 120 watts (PoE consumption + DC out and depending on power input) |
| Max. Number of Class 2 PDs | 4 |
| Max. Number of Class 3 PDs | 4 |
| Max. Number of Class 4 PDs | 4 |
| Min. Voltage | 24V (Suggest > 30V for fully charge to battery) |
| Max. Voltage | 45V |
| Max. Current | < 8.8A |
| Max. Power | < 400W |
| Type | Lithium Battery (Default) Lead-acid Battery |
| FCV | Lithium Battery (Default) fixed 26.6V Lead-acid Battery 27.2V (26.0~30.0V) |
| ACV | Lithium Battery (Default) fixed 28.7V Lead-acid Battery 29.2V (28.0~32.0V) |
| LVD (Low Voltage Disconnection) | Lithium Battery (Default) 21.3V (19.6~23.0V) Lead-acid Battery 22.2V (21.0~23.0V) |
| LVR (Low Voltage Reconnection) | Lithium Battery (Default) 24.0V (23.5~25.0V) Lead-acid Battery 23.5V (23.5~27.0V) |
| Internet Connection Type | Shares data and Internet access with users, supporting the following internet accesses: - PPPoE - Dynamic IP - Static IP - PPTP - L2TP |
| Firewall | NAT firewall with SPI (Stateful Packet Inspection) Built-in NAT server supporting Port Forwarding, and DMZ Built-in firewall with IP address/MAC address/Port/ URL filtering Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter, DoS protection |
| Routing Protocol | Static/Dynamic (RIP1 and 2) routing |
| VPN Pass-through | PPTP, L2TP, IPSec, IPv6 |
| LAN | Built-in DHCP server supporting static IP address distribution Supports UPnP, Dynamic DNS Supports IGMP Proxy Supports 802.1d STP (Spanning Tree) IP/MAC-based bandwidth control |
| Management Interface | Setting up of system/management functions Web firmware upgrade SNMP trap for alarm notification of events |
| PoE Management | Power limit by consumption and allocation PoE admin mode Per port power schedule Per port power enable/disable Power feeding priority Current per port usage and status Total power consumption PD alive check Scheduled power recycling |
| Battery Management | Current battery usage status Low voltage cut-off protection Fully-charged hold time protection |
| PLANET ONVIF IP Camera Management | Supports PLANET ONVIF IP camera discovery A maximum of four PLANET ONVIF IP cameras can be powered by one BSP-360 switch. Supports IP camera snapshot function in the LAN. |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Standards Compliance | IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3x Flow Control and Back Pressure IEEE 802.1D Spanning Tree Protocol IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus RFC 768: UDP RFC 791: IP RFC 2068 HTTP RFC 1157: SNMP v1 RFC 1902: SNMP v2c RFC 5424: Syslog |
| Operating | Temperature: -10 ~ 60 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage | Temperature: -10 ~ 70 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
© כל הזכויות שמורות לסיבים תשתיות תקשורת
פרסום בפייסבוק ע"י קרית טק
