מחיר וייעוץ למוצר הזהדברו עם יועץ ובחרו את הפתרון שמתאים לכםפרטי המוצר מצורפים אוטומטית להודעת הוואטסאפ
עד 7 ימי עסקים בלבד
בהזמנות מעל 2000 ש״ח
הכוונה וייעוץ לפני רכישה
בהזמנות אונליין באתר
PLANET IGS-6325-4UP2X — מתג תעשייתי מנוהל L3 PoE++. מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
Industrial L3 Managed PoE++ Switch. PLANET IGS-6325-4UP2X connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
PLANET IGS-6325-4UP2X · מתגים תעשייתיים
PLANET IGS-6325-4UP2X מיועד לחיבור ציוד Ethernet בתשתיות תקשורת תעשייתיות. תצורת החיבורים של הדגם מאפשרת לרכז התקני קצה בארון התקשורת ולשלב אותם ברשת המקומית, בהתאם למהירויות ולממשקים המפורטים בהמשך.
4 2.5GBASE-T RJ45 auto negotiation port Supports 2.5G/1G/100/10Mbps data rate
IEEE 802.3bt PoE++ Type-4
Single power input: 240W maximum (depending on power input) Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V.
DC 48V-54V, 8.3A max.
DIN-rail or wall-mount
IP30 aluminum case
בתכנון ארון תקשורת למפעל, מערכת בקרה או תשתית אבטחה, חשוב להתאים את מספר החיבורים ואת רוחב הפס לכל קצה. חיבורי Uplink, כאשר הם קיימים בדגם, משמשים לקישור לשאר הרשת. בממשק SFP יש להתאים את המודול, סוג הסיב ואורך הקו לשני קצות הקישור.
הדגם כולל תמיכה ב־VLAN, QoS, ACL, LACP, ERPS, SNMP, IPv6 לפי המפרט. יכולות אלה מאפשרות להתאים את הגדרות הרשת לפרויקט; מגדירים כל תכונה לפי תכנון התעבורה וממשקי הציוד המחובר.
טבלת המפרט באנגלית מרכזת את נתוני הדגם לצורך השוואה והתאמה טכנית. יש להתאים את ההזנה, החיבורים ותנאי הסביבה לערכים המפורטים. צוות סיבים מסייע בבחירת הציוד והתצורה המתאימים לפרויקט.
The PLANET IGS-6325-4UP2X connects Ethernet equipment in industrial network installations. Its port configuration brings local devices into the network, with the supported copper and fiber interfaces detailed below. Select the exact interfaces and link speeds required by the connected equipment.
For factory networks, control systems and surveillance infrastructure, plan both the number of device connections and the uplink capacity. Where SFP interfaces are provided, the transceiver type, fiber type and link distance must match the equipment at both ends. Copper and fiber ports are listed separately to make this planning easier.
The technical table below provides the model-specific information for comparison and system design. Match the power source, connectors and environmental conditions to these ratings. SIVIM can assist with equipment selection and configuration for the project.
| Specification | Details |
|---|---|
| Manufacturer / Model | PLANET IGS-6325-4UP2X |
| Copper Ports | 4 2.5GBASE-T RJ45 auto negotiation port Supports 2.5G/1G/100/10Mbps data rate |
| SFP+ Ports | 2 10GBASE-SR/LR SFP+ slots Backward compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP transceivers |
| PoE Injector Ports | 4 ports with 802.3bt PoE++ injector function, from Port-1 to Port-4 |
| Console | 1 x RJ45-to-RS232 serial port (115200, 8, N, 1) |
| Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
| Connector | Removable 6-pin terminal block for power input Pin 1/2 for Power 1, Pin 3/4 for Alarm, Pin 5/6 for Power 2 Removable 6-pin terminal block for DI/DO interface Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND |
| Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24VDC |
| Digital Input (DI) | 2 digital inputs: Level 0: -24~2.1V (±0.1V) Level 1: 2.1~24V (±0.1V) Input load to 24VDC, 10mA max. |
| Digital Output (DO) | 2 digital outputs: Open collector to 24VDC, 100mA |
| Enclosure | IP30 aluminum case |
| Installation | DIN-rail or wall-mount |
| SDRAM | 512Mbytes |
| Flash Memory | 64Mbytes |
| Dimensions (W x D x H) | 76 x 135 x 152 mm |
| Weight | 1,319g |
| Power Requirements | DC 48V-54V, 8.3A max. |
| Power Consumption | 48VDC Input: Max. 8.9 watts/30.4 BTU (Idle) Max. 379 watts/1293.2 BTU (Full load) 54VDC Input: Max. 9.2 watts/31.4 BTU (Idle) Max. 381 watts/1300 BTU (Full load) |
| ESD Protection | Contact 4KVDC; Air 8KVDC |
| Surge Protection | 2KVDC |
| LED Indicators | System: Power 1 ( Green ), Power 2 ( Green ) Alarm ( Red ) Ring ( Green ), Ring Owner ( Green ) DI/DO ( Red ) PoE Usage: 120W/240W/360W ( Amber ) Per 10/100/1G/2.5GBASE-T RJ45 Port: Data LED: 1G/2.5G LNK/ACT ( Green ) 10/100 LNK/ACT ( Amber ) PoE LED: IEEE 802.3bt Mode ( Green ) IEEE 802.3at Mode ( Amber ) Per 1G/2.5G/10GBASE-X SFP+ Port: 1G/2.5Gbps LNK/ACT ( Green ) 10Gbps LNK/ACT ( Amber ) |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 60Gbps/non-blocking |
| Throughput | 44.462Mpps@64Bytes |
| Address Table | 8K entries, automatic source address learning and aging |
| Shared Data Buffer | 32Mbits |
| Jumbo Frame | 10K bytes |
| Flow Control | IEEE 802.3x pause frame for full duplex Back pressure for half duplex |
| PoE Standard | IEEE 802.3bt PoE++ Type-4 |
| PoE Power Supply Type | End-span Mid-span BT |
| Power Pin Assignment | 802.3bt/UPoE: 1/2(-), 3/6(+), 4/5(+), 7/8(-) 802.3at/PoE: End-span: 1/2(-), 3/6(+) 802.3at/PoE: Mid-span: 4/5(+), 7/8(-) |
| PoE Power Output | Per port 48V ~ 54VDC -802.3bt Type-4 mode: maximum 95 watts -End-span mode: maximum 36 watts -Mid-span mode: maximum 36 watts -Force mode: maximum 95 watts |
| PoE Power Budget | Single power input: 240W maximum (depending on power input) Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V. |
| Number of 90W 802.3bt Type-4 PDs | 4 |
| Number of 60W 802.3bt Type-3 PDs | 4 |
| Number of 30W 802.3at Type-2 PDs | 4 |
| Enhanced PoE Mode | Standard/Legacy/Force |
| PoE Management | PD Alive Check Scheduled Power Recycling PoE Schedule PoE Usage Monitoring PoE Extension |
| Active PoE Device Live Detection | Yes |
| PoE Power Recycling | Yes, daily or predefined schedule |
| PoE Schedule | 4 schedule profiles |
| PoE Extend Mode | Yes, max. up to 160 meters |
| IP Interfaces | Max. 32 VLAN interfaces |
| Routing Table | Max. 32 static routing entries Max. 1K routing table entries |
| Routing Protocols | IPv4 RIPv2 IPv4 OSPFv2 IPv6 OSPFv3 IPv4 hardware static routing IPv6 hardware static routing |
| Port Configuration | Port disable/enable Auto-negotiation 10/100/1000/2500Mbps full and half duplex mode selection Flow control disable/enable Port link capability control |
| Port Status | Display of each port’s speed duplex mode, link status, flow control status, auto-negotiation status and trunk status |
| Port Mirroring | TX/RX/Both Many-to-1 monitor RMirror – Remote Switched Port Analyzer (Cisco RSPAN) Supports up to 5 sessions |
| VLAN | IEEE 802.1Q tagged VLAN IEEE 802.1ad Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN IP Subnet-based VLAN MVR (Multicast VLAN registration) GVRP Up to 4K VLAN groups, out of 4095 VLAN IDs |
| Link Aggregation | IEEE 802.3ad LACP/static trunk Max. 3 trunk groups with max. 6 ports per trunk group |
| Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol Supports 7 MSTP instances BPDU Guard, BPDU filtering and BPDU transparent Root Guard |
| IGMP Snooping | IPv4 IGMP (v1/v2/v3) snooping IPv4 IGMP querier mode support Supports 255 IGMP groups |
| MLD Snooping | IPv6 MLD (v1/v2) snooping, IPv6 MLD querier mode support Supports 255 MLD groups |
| Bandwidth Control | Per port bandwidth control Ingress: 10Kbps~13128Mbps Egress: 10Kbps~13128Mbps |
| Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 10ms @ 3 nodes Recovery time < 50ms @ 16 nodes Supports Major ring and sub-ring |
| Synchronization | IEEE 1588v2 PTP (Precision Time Protocol) Peer-to-peer transparent clock End-to-end transparent clock |
| QoS | Traffic classification based, strict priority and WRR 8-level priority for switching: Port number 802.1p priority 802.1Q VLAN tag DSCP/ToS field in IP packet |
| Access Control List | IP-based ACL/MAC-based ACL ACL based on: MAC Address IP Address Ethertype Protocol Type VLAN ID DSCP 802.1p Priority Up to 512 entries |
| Security | Port security IP source guard, up to 512 entries Dynamic ARP inspection, up to 1K entries Command line authority control based on user level Static MAC address, up to 64 entries |
| AAA | RADIUS client TACACS+ client |
| Network Access Control | IEEE 802.1x port-based network access control MAC-based authentication Local/RADIUS authentication |
| Basic Management Interfaces | Console; Telnet; Web browser; SNMP v1, v2c |
| Secure Management Interfaces | SSHv2, TLS v1.2, SNMPv3 |
| System Management | Firmware upgrade by HTTP protocol through Ethernet network Configuration upload/download through HTTP Remote Syslog System log LLDP protocol NTP PLANET Smart Discovery Utility PLANET CloudViewer app |
| SNMP MIBs | RFC 1213 MIB-II RFC 1493 Bridge MIB RFC 1643 Ethernet MIB RFC 2863 Interface MIB RFC 2665 Ether-Like MIB RFC 2819 RMON MIB (Group 1, 2, 3 and 9) RFC 2737 Entity MIB RFC 2618 RADIUS Client MIB RFC 2863 IF-MIB RFC 2933 IGMP-STD-MIB RFC 3411 SNMP-Frameworks-MIB RFC 4292 IP Forward MIB RFC 4293 IP MIB RFC 4836 MAU-MIB IEEE 802.1X PAE LLDP |
| Regulatory Compliance | FCC Part 15 Class A CE: EN55032 EN55035 |
| Stability Testing | IEC60068-2-32 (free fall) IEC60068-2-27 (shock) IEC60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000T IEEE 802.3ae 10GBASE-X IEEE 802.3bz 2.5/5GBASE-T IEEE 802.3x flow control and back pressure IEEE 802.3ad port trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN tagging IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3ah OAM IEEE 802.1ag Connectivity Fault Management (CFM) RFC 768 UDP RFC 783 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 RFC 3810 MLD v2 RFC 2328 OSPF v2 RFC 5340 OSPF v3 RFC 2453 RIP v2 ITU-T G.8032 ERPS Ring |
| Operating | -40 ~ 75 degrees C |
| Storage | -40 ~ 85 degrees C |
| Humidity | 5 ~ 95% (non-condensing) |
| Model | IGS-6325-4UP2X |
|---|---|
| Copper Ports | 4 2.5GBASE-T RJ45 auto negotiation port Supports 2.5G/1G/100/10Mbps data rate |
| SFP+ Ports | 2 10GBASE-SR/LR SFP+ slots Backward compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP transceivers |
| PoE Injector Ports | 4 ports with 802.3bt PoE++ injector function, from Port-1 to Port-4 |
| Console | 1 x RJ45-to-RS232 serial port (115200, 8, N, 1) |
| Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
| Connector | Removable 6-pin terminal block for power input Pin 1/2 for Power 1, Pin 3/4 for Alarm, Pin 5/6 for Power 2 Removable 6-pin terminal block for DI/DO interface Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND |
| Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24VDC |
| Digital Input (DI) | 2 digital inputs: Level 0: -24~2.1V (±0.1V) Level 1: 2.1~24V (±0.1V) Input load to 24VDC, 10mA max. |
| Digital Output (DO) | 2 digital outputs: Open collector to 24VDC, 100mA |
| Enclosure | IP30 aluminum case |
| Installation | DIN-rail or wall-mount |
| SDRAM | 512Mbytes |
| Flash Memory | 64Mbytes |
| Dimensions (W x D x H) | 76 x 135 x 152 mm |
| Weight | 1,319g |
| Power Requirements | DC 48V-54V, 8.3A max. |
| Power Consumption | 48VDC Input: Max. 8.9 watts/30.4 BTU (Idle) Max. 379 watts/1293.2 BTU (Full load) 54VDC Input: Max. 9.2 watts/31.4 BTU (Idle) Max. 381 watts/1300 BTU (Full load) |
| ESD Protection | Contact 4KVDC; Air 8KVDC |
| Surge Protection | 2KVDC |
| LED Indicators | System: Power 1 ( Green ), Power 2 ( Green ) Alarm ( Red ) Ring ( Green ), Ring Owner ( Green ) DI/DO ( Red ) PoE Usage: 120W/240W/360W ( Amber ) Per 10/100/1G/2.5GBASE-T RJ45 Port: Data LED: 1G/2.5G LNK/ACT ( Green ) 10/100 LNK/ACT ( Amber ) PoE LED: IEEE 802.3bt Mode ( Green ) IEEE 802.3at Mode ( Amber ) Per 1G/2.5G/10GBASE-X SFP+ Port: 1G/2.5Gbps LNK/ACT ( Green ) 10Gbps LNK/ACT ( Amber ) |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 60Gbps/non-blocking |
| Throughput | 44.462Mpps@64Bytes |
| Address Table | 8K entries, automatic source address learning and aging |
| Shared Data Buffer | 32Mbits |
| Jumbo Frame | 10K bytes |
| Flow Control | IEEE 802.3x pause frame for full duplex Back pressure for half duplex |
| PoE Standard | IEEE 802.3bt PoE++ Type-4 |
| PoE Power Supply Type | End-span Mid-span BT |
| Power Pin Assignment | 802.3bt/UPoE: 1/2(-), 3/6(+), 4/5(+), 7/8(-) 802.3at/PoE: End-span: 1/2(-), 3/6(+) 802.3at/PoE: Mid-span: 4/5(+), 7/8(-) |
| PoE Power Output | Per port 48V ~ 54VDC -802.3bt Type-4 mode: maximum 95 watts -End-span mode: maximum 36 watts -Mid-span mode: maximum 36 watts -Force mode: maximum 95 watts |
| PoE Power Budget | Single power input: 240W maximum (depending on power input) Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V. |
| Number of 90W 802.3bt Type-4 PDs | 4 |
| Number of 60W 802.3bt Type-3 PDs | 4 |
| Number of 30W 802.3at Type-2 PDs | 4 |
| Enhanced PoE Mode | Standard/Legacy/Force |
| PoE Management | PD Alive Check Scheduled Power Recycling PoE Schedule PoE Usage Monitoring PoE Extension |
| Active PoE Device Live Detection | Yes |
| PoE Power Recycling | Yes, daily or predefined schedule |
| PoE Schedule | 4 schedule profiles |
| PoE Extend Mode | Yes, max. up to 160 meters |
| IP Interfaces | Max. 32 VLAN interfaces |
| Routing Table | Max. 32 static routing entries Max. 1K routing table entries |
| Routing Protocols | IPv4 RIPv2 IPv4 OSPFv2 IPv6 OSPFv3 IPv4 hardware static routing IPv6 hardware static routing |
| Port Configuration | Port disable/enable Auto-negotiation 10/100/1000/2500Mbps full and half duplex mode selection Flow control disable/enable Port link capability control |
| Port Status | Display of each port’s speed duplex mode, link status, flow control status, auto-negotiation status and trunk status |
| Port Mirroring | TX/RX/Both Many-to-1 monitor RMirror – Remote Switched Port Analyzer (Cisco RSPAN) Supports up to 5 sessions |
| VLAN | IEEE 802.1Q tagged VLAN IEEE 802.1ad Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN IP Subnet-based VLAN MVR (Multicast VLAN registration) GVRP Up to 4K VLAN groups, out of 4095 VLAN IDs |
| Link Aggregation | IEEE 802.3ad LACP/static trunk Max. 3 trunk groups with max. 6 ports per trunk group |
| Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol Supports 7 MSTP instances BPDU Guard, BPDU filtering and BPDU transparent Root Guard |
| IGMP Snooping | IPv4 IGMP (v1/v2/v3) snooping IPv4 IGMP querier mode support Supports 255 IGMP groups |
| MLD Snooping | IPv6 MLD (v1/v2) snooping, IPv6 MLD querier mode support Supports 255 MLD groups |
| Bandwidth Control | Per port bandwidth control Ingress: 10Kbps~13128Mbps Egress: 10Kbps~13128Mbps |
| Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 10ms @ 3 nodes Recovery time < 50ms @ 16 nodes Supports Major ring and sub-ring |
| Synchronization | IEEE 1588v2 PTP (Precision Time Protocol) Peer-to-peer transparent clock End-to-end transparent clock |
| QoS | Traffic classification based, strict priority and WRR 8-level priority for switching: Port number 802.1p priority 802.1Q VLAN tag DSCP/ToS field in IP packet |
| Access Control List | IP-based ACL/MAC-based ACL ACL based on: MAC Address IP Address Ethertype Protocol Type VLAN ID DSCP 802.1p Priority Up to 512 entries |
| Security | Port security IP source guard, up to 512 entries Dynamic ARP inspection, up to 1K entries Command line authority control based on user level Static MAC address, up to 64 entries |
| AAA | RADIUS client TACACS+ client |
| Network Access Control | IEEE 802.1x port-based network access control MAC-based authentication Local/RADIUS authentication |
| Basic Management Interfaces | Console; Telnet; Web browser; SNMP v1, v2c |
| Secure Management Interfaces | SSHv2, TLS v1.2, SNMPv3 |
| System Management | Firmware upgrade by HTTP protocol through Ethernet network Configuration upload/download through HTTP Remote Syslog System log LLDP protocol NTP PLANET Smart Discovery Utility PLANET CloudViewer app |
| SNMP MIBs | RFC 1213 MIB-II RFC 1493 Bridge MIB RFC 1643 Ethernet MIB RFC 2863 Interface MIB RFC 2665 Ether-Like MIB RFC 2819 RMON MIB (Group 1, 2, 3 and 9) RFC 2737 Entity MIB RFC 2618 RADIUS Client MIB RFC 2863 IF-MIB RFC 2933 IGMP-STD-MIB RFC 3411 SNMP-Frameworks-MIB RFC 4292 IP Forward MIB RFC 4293 IP MIB RFC 4836 MAU-MIB IEEE 802.1X PAE LLDP |
| Regulatory Compliance | FCC Part 15 Class A CE: EN55032 EN55035 |
| Stability Testing | IEC60068-2-32 (free fall) IEC60068-2-27 (shock) IEC60068-2-6 (vibration) |
| Standards Compliance | IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000T IEEE 802.3ae 10GBASE-X IEEE 802.3bz 2.5/5GBASE-T IEEE 802.3x flow control and back pressure IEEE 802.3ad port trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN tagging IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3ah OAM IEEE 802.1ag Connectivity Fault Management (CFM) RFC 768 UDP RFC 783 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 RFC 3810 MLD v2 RFC 2328 OSPF v2 RFC 5340 OSPF v3 RFC 2453 RIP v2 ITU-T G.8032 ERPS Ring |
| Operating | -40 ~ 75 degrees C |
| Storage | -40 ~ 85 degrees C |
| Humidity | 5 ~ 95% (non-condensing) |
© כל הזכויות שמורות לסיבים תשתיות תקשורת
פרסום בפייסבוק ע"י קרית טק
